Enquire Now
Sachin Steel Centre — Full Menu
+91 9029534448 sachinsteel51@hotmail.com

Nitinol Grade 5 Sheet / Plate

HOME → Materials → Nitinol → Nitinol Grade 5 Sheet / Plate

Sachin Steel Product Banner_17 Sept_004

Nitinol Grade 5 Sheet / Plate refers to flat nickel-titanium material selected for applications that require shape memory, superelastic response, high recoverable strain, corrosion resistance and precise dimensional control. Nitinol sheet and Nitinol plate can be supplied in application-specific thicknesses, widths, lengths, surface conditions, and transformation temperatures for medical, aerospace, robotics, electronics, and industrial applications. Sachin Steel Centre supplies Nitinol sheet and plate for precision applications with material documentation and custom requirements available as specified.

Request a Quote
Table Of Content

Technical Data

Nitinol Grade 5 Sheet / Plate Specifications

Specification

Detail

Material

Nickel titanium Nitinol

Applicable Standard

ASTM F2063, ASME SF2063

Nickel Content

Nominally 54.5 to 57.0 percent

Titanium

Balance

Product Form

Sheet and plate

Thickness

0.076 mm to 2.5 mm, other thicknesses on request

Width

Up to 90 mm standard, larger sizes on request

Length

Up to 500 mm standard, custom lengths on request

Surface

Pickled, ground, polished or other agreed condition

Documentation

Material test certificate and agreed inspection documents

Chemical Composition of Nitinol Grade 5 Plate / Sheet

Nickel

Titanium

Carbon (max)

Oxygen + Nitrogen (max)

Hydrogen (max)

Iron (max)

Cobalt (max)

Niobium (max)

54.5 to 57.0%

Balance

0.050%

0.050%

0.005%

0.050%

0.050%

0.025%

Chromium and copper are each held to 0.010 percent maximum under ASTM F2063. The exact chemical limits should be confirmed against the applicable purchase specification and material certificate.

Physical Properties of Nitinol Grade 5 Sheet / Plate

Density

Melting Temperature

Thermal Conductivity

Electrical Resistivity

6.45 g/cm³

Approximately 1310°C

Austenite 0.18 W/cm°C, Martensite 0.086 W/cm°C

Austenite 82 × 10⁻⁶ Ωcm, Martensite 76 × 10⁻⁶ Ωcm

Elastic modulus and thermal expansion vary between the martensitic and austenitic phases and should be treated as typical information unless a specific product specification provides a guaranteed value.

Nitinol Grade 5 Sheet / Plate Mechanical Properties

Material Condition

Ultimate Tensile Strength

Elongation

Upper Plateau Stress

Permanent Set After 6% Strain

Active Af Temperature

A

≥1300 MPa

≥10%

≥480 MPa

<0.5%

10±7°C

B

≥1150 MPa

≥10%

≥440 MPa

<0.5%

17±7°C

C

≥1000 MPa

≥10%

≥400 MPa

<0.5%

25±5°C

D

≥950 MPa

≥10%

≥300 MPa

<0.5%

35±5°C

E

≥550 MPa

≥15%

≥200 MPa

<0.5%

35±8°C to 110±8°C

Mechanical testing is reported at 22 ± 2°C. Material condition should be confirmed against the applicable purchase specification and material certificate.

Shape Memory Nitinol Sheet and Superelastic Nitinol Sheet

Feature

Shape Memory Nitinol Sheet

Superelastic Nitinol Sheet

Main Behaviour

Thermal shape recovery

Recoverable deformation

Primary Trigger

Temperature change

Mechanical loading and unloading

Important Parameter

Af temperature

Transformation temperature and stress response

Typical Use

Actuators and thermal mechanisms

Flexible and resilient components

Functional Requirement

Correct shape setting

Correct stress and strain response

Processing Importance

High

High

Application Selection

Based on thermal activation

Based on operating temperature and loading

For applications where the material must perform a defined transformation at a specific temperature, the required Af temperature should be discussed before ordering.

Frequently Asked Questions

No. Nitinol is a nickel-titanium shape memory alloy, while Titanium Grade 5 is Ti 6Al 4V. Titanium Grade 5 is a different alloy and does not provide the same shape memory and superelastic behaviour associated with Nitinol.

Nitinol Grade 5 is not a general ASTM grade designation for nickel titanium. Nitinol is normally specified by its applicable material specification, chemical composition, transformation characteristics, and material condition. ASTM F2063 26 is an important specification for applicable wrought nickel titanium shape memory alloy products.

Nitinol Grade 5 Sheet / Plate is a search term used for flat nickel-titanium material. Buyers using this term should confirm that they require Nitinol rather than Titanium Grade 5, because Titanium Grade 5 refers to Ti-6Al-4V.

Nitinol sheets are used for specialised medical, dental, aerospace, robotics, electronics, industrial automation and precision engineering applications where shape recovery, superelasticity, flexibility and corrosion resistance are required.

The terms sheet and plate generally describe flat product thickness categories, but the exact distinction depends on the governing specification and purchaser requirement. For Nitinol, the applicable standard and required dimensions should be confirmed before ordering.

Sachin Steel Centre offers a broader range of Nitinol products for applications requiring shape memory and superelastic characteristics.

Request a Quote for Nitinol Grade 5 Sheet / Plate

For Nitinol Grade 5 Sheet / Plate enquiries, provide the required thickness, width, length, quantity, surface finish, material condition, application and transformation temperature where applicable. Sachin Steel Centre can review the requirement and help identify the appropriate Nitinol Sheet or Nitinol Plate for the intended application.

Request a Quote
Pan-India Supply Network & Export Worldwide

Pan-India

Supply Network

Map of India supply network
45+ Cities Served

Export

Worldwide

Export worldwide shipping routes

Our Global Export Regions

Sachin-Steel_Product-CTA

Titanium

Materials

Our Products

    Enquire Now